Epoxy gravel floor sealer
At a glance
- Especially for gravel floors
- Good flowability
- UV stable
Do you need a sealer to seal the open structure of an epoxy gravel floor so that you get a stone carpet? Then Variopox Topgel is the sealer you are looking for! Variopox Topgel is a solvent-free thixotropic mixing paste based on an epoxy resin.
The advantage of this sealer is that water can no longer sink through the floor. And no more dust will accumulate in the small pores of the floor. This sealer makes it easier to vacuum the epoxy gravel floor and to keep it clean. In addition, the floor will also shed fewer stones.
Benefits of the sealer
Using this sealer offers several advantages. Besides being more hygienic due to the easy cleaning and maintenance, it is also easy to apply. Below is an overview of the advantages of a sealer for your gravel floor:
- Resistant to UV radiation.
- Easy to apply with a window squeegee or roller.
- Offers good water resistance.
- Hygienic due to easy cleaning and maintenance.
Order your epoxy gravel floor sealer
Do you have an epoxy gravel floor or are you planning to lay it? If so, use this sealer as a floor coating! The super fast morning or evening delivery means you can start using the coating today. Do you have any questions about its use or another question? We can be reached by phone at +3185 0220090 or by e-mail at support@polyestershoppen.com. It is also possible to send us a chat message via Whatsapp. Our customer service is ready for you!
Specifications
Contents: set of 10 kg (for 10-15 m2)
Mixing ratio: 67:33 (based on weight)
Gloss: transparent / semi-gloss
Density: approx. 1.1 g/cm3
Consumption: approx. 0.5 - 0.8 kg/ m2
Processing time: 20 minutes
Dust dry after: 4 hours
Walkable after: 18 hours
Fully hardened after: 2 days
Product properties
The key technical properties clearly listed in one place.
- Article number
- VLO000212
-
The technical product category, such as primer, resin, hardener or cleaner. It explains the product's purpose and helps you find other products with a similar function.
- Grindvloer
-
The resin family or system that a hardener, additive or reinforcement material can be combined with, such as epoxy, polyester or vinyl ester. Compatibility depends on the complete system, not just the general resin type.
- Epoxy
-
The waiting time before a coating, floor or bonded joint can withstand a specified load, such as light foot traffic or gentle handling. Resistance often increases as curing continues; full mechanical and chemical resistance may be reached later.
- Foot traffic: 18 hours
-
Density describes the mass of a material per unit volume. Values may be given in g/cm³, kg/L or kg/m³; 1 g/cm³ equals 1 kg/L. For example, one litre of a liquid with a density of 1.2 kg/L weighs approximately 1.2 kg. Density helps convert between weight and volume, but it can vary with temperature.
- Approximately 1.1 kg/L
-
Mixing ratio indicates how much of each component is needed, for example resin (A) and hardener (B). A ratio of 100:50 by weight means 100 grams of A to 50 grams of B; by volume you might use millilitres. Weight and volume ratios are not necessarily the same because the components may have different densities. Accurate measuring is important for proper curing.
- 67:33 (by weight)
-
A paint or varnish layer is dust-dry when settling dust is less likely to stick to the surface. It may not yet be touch-dry, ready for overcoating or suitable for loading; these are different stages of drying and curing.
- 4 hours
-
Curing time is the period a product needs to reach a specified stage of cure. It is usually given in hours or days, often at a reference temperature such as 20 °C. A product may be tack-free or safe to handle before reaching its full mechanical and chemical resistance. Film thickness and mixed quantity may also affect the time.
- 2 days
-
Consumption or coverage describes how much product is needed for a given surface area. Consumption may be stated in g/m² or kg/m², while coverage is often given in m²/L or m²/kg. A consumption of 0.2 kg/m² means a theoretical 200 grams per square metre. Actual use depends on film thickness, substrate absorbency, application method and waste.
- Approximately 0.5-0.8 kg/m²
- Net contents
- 10 kg kit (for 10-15 m²)
-
Working time is the period during which a product remains workable after mixing or activation, usually given in minutes at a specified temperature, often 20 °C. With reactive resins, the chemical reaction also continues in the mixing container, and larger quantities or higher temperatures can shorten this time. Working time is different from gel time and full curing time.
- Approximately 20 minutes
Safety information
Read the warnings and use appropriate protective equipment before handling the product.