Sika Primer-215
At a glance
- 1-component primer
- Primer for plastics and wood
- Contents: 250 ml
Sika Primer-215 is a colourless to light yellow, solvent-based primer that reacts with moisture to form a thin film. This film acts as a bonding layer between the substrate and the adhesive. Sika Primer-215 is specifically formulated for pre-treating surfaces prior to the application of Sika's one-component polyurethane adhesives and sealants.
Suitable substrates
Sika Primer-215 is used to improve adhesion to many plastics (such as GRP, epoxy, PVC, ABS) and wood. Because of the wide variety of plastics, preliminary tests should be carried out on original substrates under production conditions. It is also commonly used when bonding rubber components, such as fender strips.
Directions for use
- Clean the surface thoroughly, ensuring it is dry and free from grease, oil, dust, or other contaminants. Adhesion can be improved by pre-treating the surface through sanding, cleaning, activation or a combination of these methods.
- Apply a thin, even coat of Sika Primer-215 using a brush, felt or foam roller, ensuring complete coverage.
- The ideal application and surface temperature are between 15 °C and 25 °C.
- Apply the primer in a single coat, ensuring complete coverage in one application.
- Carefully close the container immediately after use.
Specifications
Contents: 250 ml
Chemical base: solvent-based polyurethane solution
Colour: light yellow
Solids content: 34%
Application temperature: 5-40 °C
Application method: brush, felt or foam roller
Consumption: 50 ml/m² (depending on substrate porosity)
Flash-off time: 30 minutes at ≥ 15 °C (maximum 24 hours)
Shelf life: 12 months (store in a sealed, upright container in a dry place at ≤ 25 °C)
Product properties
The key technical properties clearly listed in one place.
- Article number
- LIJ002272
-
The recommended application temperature range indicates the conditions under which the product can generally be applied and cured properly. Three temperatures matter:
- Air: the temperature in the workshop or outdoors.
- Substrate: the temperature of the surface being treated.
- Product: the temperature of the resin, adhesive or coating itself.
A cold substrate can cause condensation and affect adhesion. At higher temperatures, two-component products may react faster, reducing their working time. Check the dew point and follow the product instructions.
- 5-40 °C
-
The chemical base describes the chemistry of an adhesive, sealant, resin or coating, such as epoxy, polyester, polyurethane, (methyl)methacrylate or a hybrid polymer. It affects curing, flexibility and adhesion. Products with the same chemical base are not necessarily suitable for the same applications.
- solvent-based polyurethane solution
-
The period for which an unopened product remains usable under the specified storage conditions. Check whether the period starts from the manufacturing date or another date. Shelf life may be shorter after opening, especially for products sensitive to air or moisture.
- 12 months
-
Solids content is the proportion of material remaining after volatile components have evaporated from a coating. It is stated as a percentage by weight or by volume (%); these are not interchangeable. Volume solids content helps estimate dry film thickness: with 60% volume solids, a 100 µm wet film will theoretically produce approximately 60 µm of dry film.
- Approximately: 34%
-
Consumption or coverage describes how much product is needed for a given surface area. Consumption may be stated in g/m² or kg/m², while coverage is often given in m²/L or m²/kg. A consumption of 0.2 kg/m² means a theoretical 200 grams per square metre. Actual use depends on film thickness, substrate absorbency, application method and waste.
- 50 ml/m²
- Net contents
- 250 ml
-
The application or processing methods specified by the manufacturer, such as brushing, rolling, spraying, casting or hand laminating. The chosen method can affect consumption, layer thickness and finish.
- Brush, Foam applicator, Felt applicator