Epifanes Gold Paint
At a glance
- One-component gold paint
- For decorative applications
- Contents: 250 ml
Epifanes Gold Paint is a single-component gold paint with excellent coverage. It is ideal for decorative applications on board, such as lettering wooden nameplates, enhancing wood, or applying a gold decorative trim.
Applications of Epifanes Gold Paint
- Lettering wooden nameplates (indoors and outdoors).
- Enhancing stone, steel, wood, and iron in combination with the appropriate primer or over existing well-adhering paint and varnish systems.
- Creating gold lettering and/or gold trim.
Directions for use
Follow these steps to apply Epifanes Gold Paint correctly:
- Ensure the surface is clean, dry, grease-free, and well-sanded.
- On bare polyester, steel, wood, stone, or zinc, always apply a coat of Epifanes Multi Marine Primer first and sand it with P180 grit.
- Stir the gold paint well before and during use.
- For an even, opaque gold finish, apply at least 3 coats. Do not apply wet-on-wet and avoid overly thick layers to prevent sagging or drying problems. Apply the gold paint in smooth strokes without repeatedly brushing over the same area.
- For outdoor use, an additional protective layer is required. After 48 hours of drying, the gold paint can be finished without sanding using two-component Epifanes Poly-urethane Yacht Paint (high gloss) for maximum UV protection, or use Epifanes Clear Varnish (single-component) for a warm finish (this slightly darkens the colour).
Specifications
Contents: 250 ml
Colour: gold
Gloss: semi-gloss
Thinner: Epifanes Brush Thinner
Application temperature: minimum 10°C, maximum 28°C
Dust dry after: 1-2 hours (at 20°C)
Recoatable with the same paint: 9-12 hours
Recoatable with varnish: 48 hours
Recommended film thickness: 100-120 µm wet = 50-60 µm dry
Coverage: 2-2.5 m2 per 250 ml (50 µm dry film)
Density: 1.05 kg/dm3 (at 20°C)
Product properties
The key technical properties clearly listed in one place.
- Article number
- LAK002268
-
The technical product category, such as primer, resin, hardener or cleaner. It explains the product's purpose and helps you find other products with a similar function.
- 1K paint
-
The recommended layer thickness is the thickness at which you apply each coat of paint, coating or resin. It is usually given in micrometres (µm) or millimetres (mm).
- Wet film thickness: the thickness immediately after application.
- Dry film thickness: the thickness after drying or curing.
For a coating with 60% solids by volume, a wet film of 100 µm will theoretically produce a dry film of approximately 60 µm. Film thickness affects coverage, protection and drying. Always check whether the manufacturer specifies wet or dry film thickness.
- 100-120 µm wet (= 50-60 µm dry)
-
The recommended application temperature range indicates the conditions under which the product can generally be applied and cured properly. Three temperatures matter:
- Air: the temperature in the workshop or outdoors.
- Substrate: the temperature of the surface being treated.
- Product: the temperature of the resin, adhesive or coating itself.
A cold substrate can cause condensation and affect adhesion. At higher temperatures, two-component products may react faster, reducing their working time. Check the dew point and follow the product instructions.
- 10-28 °C
-
Density describes the mass of a material per unit volume. Values may be given in g/cm³, kg/L or kg/m³; 1 g/cm³ equals 1 kg/L. For example, one litre of a liquid with a density of 1.2 kg/L weighs approximately 1.2 kg. Density helps convert between weight and volume, but it can vary with temperature.
- 1.05 kg/dm³ (20 °C)
-
A paint or varnish layer is dust-dry when settling dust is less likely to stick to the surface. It may not yet be touch-dry, ready for overcoating or suitable for loading; these are different stages of drying and curing.
- 1-2 hours (20 °C)
-
Consumption or coverage describes how much product is needed for a given surface area. Consumption may be stated in g/m² or kg/m², while coverage is often given in m²/L or m²/kg. A consumption of 0.2 kg/m² means a theoretical 200 grams per square metre. Actual use depends on film thickness, substrate absorbency, application method and waste.
- 2-2.5 m² per 250 ml (50 µm dry film)
-
A specific thinner that can be used, where permitted, to adjust a product's application properties or viscosity. The correct thinner and maximum quantity depend on the product. Incorrect thinning can affect coverage, drying and curing.
- Epifanes Paint Thinner
- Net contents
- 250 ml