Epifanes Polyurethane Clear Varnish (satin)
At a glance
- UV-resistant clear varnish
- Scratch, impact, wear-resistant
- Satin gloss finish
Epifanes Polyurethane is a two-component satin clear varnish with exceptionally high durability for outdoor use. This varnish is resistant to scratches, impacts, and abrasion, and provides excellent protection against water and weather conditions. Thanks to the built-in UV filter, wood remains protected against discoloration for a long time.
Benefits of satin clear varnish
- High-quality two-component satin gloss varnish.
- Built-in UV filters for optimal protection against discoloration.
- Excellent scratch, impact, and wear resistance.
- Weather- and water-resistant.
Applications
Epifanes Polyurethane Clear Varnish is suitable for:
- Complete varnish systems on new, non-moving wood (interior and exterior, above the waterline).
- UV protection over Epifanes PP Varnish Extra, epoxy resin or an epoxy sealer/primer layer.
- Maintenance of existing two-component varnish systems, regardless of brand.
- Use as a clearcoat over degreased and sanded Epifanes Polyurethane Yacht Paint in colour.
Properties
| Packaging | Basis | Hardener |
| 750 gr (suitable for approx. 9 m2) | 500 gr | 250 gr |
Gloss: satin
Colour: transparent
Mixing ratio: 100:50 (2 to 1)
Pot life: 3-4 hours (20°C)
Recommended film thickness: 60-70 µm wet = 30-35 µm dry
Minimum application temperature: 12°C - 30°C
Relative humidity: 50% - 75%
Coverage: 11 m2 per kg
Dust dry: 2 hours (20°C)
Recoatable: 24 hours (20°C)
Density: 1.070 gr/dm3
VOC content: 538 gram/litre
Thinner: Epifanes Polyurethane brush thinner
Product properties
The key technical properties clearly listed in one place.
- Article number
- LAK002204
-
Gloss level indicates how much light a dry paint or coating reflects and how the finished surface looks.
- Matt: little reflection and a subdued appearance.
- Satin: a gentle sheen between matt and high gloss.
- High gloss: stronger reflections and a more pronounced colour, although surface imperfections may become more visible.
Gloss can be measured in gloss units (GU) at a specified angle. Terms such as matt and satin do not necessarily mean exactly the same thing across manufacturers. Substrate condition and application also affect the final appearance.
- Silk gloss / Satin
-
The technical product category, such as primer, resin, hardener or cleaner. It explains the product's purpose and helps you find other products with a similar function.
- 2K clear coat
-
Minimum application temperature is the lowest temperature at which a product may be used according to the manufacturer. The limit can apply to the air, substrate and product itself.
At lower temperatures, resins and coatings can become thicker and cure more slowly. Moisture can also condense on a cold substrate and reduce adhesion. Check the dew point and measure the surface temperature before starting. A longer drying time does not automatically make application below the specified minimum acceptable.
- 12 °C
-
The recommended layer thickness is the thickness at which you apply each coat of paint, coating or resin. It is usually given in micrometres (µm) or millimetres (mm).
- Wet film thickness: the thickness immediately after application.
- Dry film thickness: the thickness after drying or curing.
For a coating with 60% solids by volume, a wet film of 100 µm will theoretically produce a dry film of approximately 60 µm. Film thickness affects coverage, protection and drying. Always check whether the manufacturer specifies wet or dry film thickness.
- 60-70 µm wet (= 30-35 µm dry)
-
Density describes the mass of a material per unit volume. Values may be given in g/cm³, kg/L or kg/m³; 1 g/cm³ equals 1 kg/L. For example, one litre of a liquid with a density of 1.2 kg/L weighs approximately 1.2 kg. Density helps convert between weight and volume, but it can vary with temperature.
- 1.070 g/dm³
-
Humidity during application is given as relative humidity, usually in percent (% RH). It indicates how much water vapour the air contains compared with the maximum it can hold at that temperature. Excessive humidity can interfere with drying or adhesion of some coatings. Also check that the substrate is dry enough and free from condensation.
- 50% - 75%
-
The overcoating interval tells you when the next layer of paint, varnish or coating may be applied. Many multi-coat systems specify both a minimum and a maximum interval:
- Minimum overcoating time: the previous layer is dry or cured enough to accept another coat.
- Maximum overcoating time: the period during which the next coat can bond without extra surface preparation under the stated conditions.
Overcoating too early can affect drying or the finish. Once the maximum interval has passed, cleaning and sanding may be needed to ensure adhesion between coats. Temperature and film thickness affect the waiting times.
- 1 day (20 °C)
-
A paint or varnish layer is dust-dry when settling dust is less likely to stick to the surface. It may not yet be touch-dry, ready for overcoating or suitable for loading; these are different stages of drying and curing.
- 2 hours (20 °C)
-
Consumption or coverage describes how much product is needed for a given surface area. Consumption may be stated in g/m² or kg/m², while coverage is often given in m²/L or m²/kg. A consumption of 0.2 kg/m² means a theoretical 200 grams per square metre. Actual use depends on film thickness, substrate absorbency, application method and waste.
- 11 m²/kg
-
A specific thinner that can be used, where permitted, to adjust a product's application properties or viscosity. The correct thinner and maximum quantity depend on the product. Incorrect thinning can affect coverage, drying and curing.
- Epifanes Polyurethane Brush Thinner
- Net contents
- 750 ml
-
Working time is the period during which a product remains workable after mixing or activation, usually given in minutes at a specified temperature, often 20 °C. With reactive resins, the chemical reaction also continues in the mixing container, and larger quantities or higher temperatures can shorten this time. Working time is different from gel time and full curing time.
- Approximately 180-240 minutes (at 20 °C)
-
VOC content (volatile organic compounds) indicates the amount of these substances in a product, usually expressed in g/L (grams per litre). They may evaporate during application and drying. The value describes the composition, but actual exposure also depends on how much is used, ventilation and the application method.
- 538 g/L
Reviews
Frequently bought together
Useful additions for your project.