RESION PU Tyre Proof Finish
- PU topcoat for cast floors
- Resistant to car tyres
- Non-yellowing
RESION Tyre Proof Finish is a two-component, water-based, extremely hard polyurethane-based top layer. This strong PU satin gloss coating extends the lifespan of your epoxy or PU cast floor and increases the resistance to chemicals (hair dye, cleaning products, etc.) and plasticizers (for example from rubber).
PU Tyre Proof Finish is stronger than RESION PU Matte Gloss, making it suitable for outdoor applications. Polyurethane flooring is also resistant to rubber migration from car tyres. Finishing your cast floor with this clear coating also reduces dirt adhesion and simplifies floor maintenance.
Features RESION PU Tyre Proof Finish
- Resistant to rubber migration from car tyres, chemicals (hair dye, cleaning products, etc.)
- Water-based.
- Non-yellowing (aliphatic).
- Easy to clean.
- Low VOC level.
Instructions for use
Before you begin, it is important that the substrate is properly pre-treated. The substrate must be sound and sufficiently compressive (at least 25 N/mm2), with a minimum bond strength of 1.5 N/mm2. The substrate must be clean, dry, and free of dirt, oil, grease, and other contaminants. If the substrate is more than 48 hours old, an adhesion test should always be performed. Then follow the instructions below to correctly apply RESION PU Tyre Proof Finish:
- Add component B to component A while stirring.
- Mix thoroughly for approximately 3 minutes to obtain a homogeneous mixture. Also scrape the bottom and sides of the container.
- Allow to pre-react for 10 minutes.
- Pour the mixture through the provided sieve into a clean bucket and mix thoroughly for another minute to avoid unmixed parts.
Tip: make sure the mixing basket is completely below the liquid level. Always mix at the highest possible speed to ensure the best possible emulsification. While mixing, a nice swirl should form in the bucket, but under no circumstances should the coating dribble or splash. Continue mixing at low speed as soon as this happens.
- After mixing, you have a processing time of approximately 30 minutes at a temperature of 20°C.
- Pour the mixed components into a paint tray.
- Apply the coating evenly using a velor roller.
- Work quickly and always wet. Do not work too quickly to avoid drying.
- Try to reduce drafts to a minimum during application (keep windows and doors closed). After applying the coating, it is important to ventilate the room to avoid surface disturbance.
- Allow the polyurethane coating to cure after application (see technical properties for curing times).
- For increased abrasion resistance and additional UV protection, you can apply an additional coat of Tyre Proof Finish after 24 hours and within 48 hours. The coating can be topcoated with an additional coat of Coating PU TR.
Dew point: also be careful of condensation. The temperature of the substrate and the uncured material must be at least 3ºC higher above the dew point to avoid the risk of condensation or whitening of the finish.
Product properties
| Contents | Number of m2 | Basis (FS801) | Hardener (FS812) |
| 2.5 kg | 15-20 m2 | 1.95 kg | 0.55 kg |
Mixing ratio: 78:22 (parts by weight)
Processing time: 30 minutes (20°C)
Dust-proof: 24 hours (20°C)
Dry to walk on: 48 hours (20°C)
Light duty: 72 hours (20°C)
Complete curing: 7 days (20°C)
Consumption: 125-150 gr/m2
Volume solids: approx. 38%
Viscosity: 1.200-1.400 mPa.s
Persoz hardness: > 250
Density: 1.04 g/cm3)
Abrasion resistance: 50 mg
Adhesion strength: > 1.5 ( concrete fracture)
Shelf life: up to 6 months after production date in original, sealed, unopened and undamaged packaging, stored dry between +5 ºC and +30 ºC.
We have a number of recommendations for working safely with polymers. At Polyestershoppen you will not only find the polymers themselves, but you can also purchase all the protective equipment you need from us. If you have any doubts or questions, please contact our customer service. We can give you advice on how to work safely with polymers.
FS802 | RESION PU TireProof Finish | Basis | 1,95 kg
Safety equipment
Waarschuwing
| Code | Description |
|---|---|
| H317 | May cause an allergic skin reaction. |
| H412 | Harmful to aquatic life with long lasting effects. |
| P101 | If medical advice is needed, have product container or label at hand. |
| P102 | Keep out of reach of children. |
| P261 | Avoid breathing dust/fume/gas/mist/vapours/spray. |
| P280 | Wear protective gloves/protective clothing/eye protection/face protection. |
| P302+P352 | IF ON SKIN: Wash with plenty of water/… |
| P333+P313 | If skin irritation or rash occurs: Get medical advice/attention. |
| P362+P364 | Take off contaminated clothing and wash it before reuse. |
| P501B | Dispose of contents/container in accordance with in accordance with local regulation |
FS812 | RESION PU TireProof Finish | Hardener | 0,55 kg
Safety equipment
Waarschuwing
| Code | Description |
|---|---|
| H317 | May cause an allergic skin reaction. |
| H332 | Harmful if inhaled. |
| H335 | May cause respiratory irritation. |
| H412 | Harmful to aquatic life with long lasting effects. |
| P101 | If medical advice is needed, have product container or label at hand. |
| P102 | Keep out of reach of children. |
| P261 | Avoid breathing dust/fume/gas/mist/vapours/spray. |
| P280 | Wear protective gloves/protective clothing/eye protection/face protection. |
| P302+P352 | IF ON SKIN: Wash with plenty of water/… |
| P333+P313 | If skin irritation or rash occurs: Get medical advice/attention. |
| P405 | Store locked up. |
| P501B | Dispose of contents/container in accordance with in accordance with local regulation |
| EUH204 | Contains isocyanates. May produce an allergic reaction. |
| MDI | As from 24 August 2023 adequate training is required before industrial or professional use |
