Tec7 Trans Inox
At a glance
- Semi-transparent sealant
- Watertight and airtight
- Super strong, permanently elastic
Tec7 Trans Inox is a semi-transparent sealant with stainless steel pigments, ideal for a clean and durable finish. The sealant visually adapts to the colour of the substrate, masking gaps and colour transitions, while remaining highly elastic and exceptionally strong after curing. Trans Inox is also free from solvents and isocyanates and is suitable for use on most building materials.
Features of Tec7 Trans Inox
- Semi-transparent and visually adapts to the colour of the substrate.
- Masks gaps and colour transitions for a seamless finish.
- Fast curing, permanently elastic and exceptionally strong.
- Free from solvents and isocyanates; nearly odourless.
- Suitable for mirrors and natural stone without leaving marks.
- Suitable for damp and smooth surfaces.
- Mould- and bacteria-resistant.
- Watertight and airtight.
- Suitable for most building materials.
Directions for use
- Application temperature: +5 °C to +40 °C.
- Ensure the substrate is clean and free from dust and grease. Use Tec7 Prepare & Finish to clean and degrease the substrate. It is also suitable for finishing and removing uncured Tec7 polymers. For heavily soiled surfaces, use Tec7 Cleaner.
- Apply Tec7 Trans Inox using a suitable caulking gun. An adhesive layer thickness of 3 mm is recommended.
- Always perform an adhesion test before applying to plastics, powder coatings, exotic woods or bituminous materials. Reinforce weak or porous substrates with Poxy Primer first.
-
Due to the wide variety of paints and coatings available, preliminary testing is recommended. Alkyd resin-based products may delay the drying process.
Properties
Contents: 310 ml cartridge
Base: MS polymer
Consistency: elastic paste
Colour: stainless steel/aluminium with a transparent finish
Extrusion rate: 160 g/min (5 bar / 3 mm / 23 °C)
Application gun: caulking gun for 290-310 ml cartridges
Skin formation: 5 minutes (23 °C, 50% RH)
Tack-free time: 40 minutes (23 °C, 50% RH)
Full curing: 24-72 hours (23 °C, 50% RH)
Adhesion:
- Good adhesion to: tiles, cement, natural stone, wood, concrete, glass and aluminium.
- Poor adhesion to: PE, PP, PTFE and bitumen.
UV resistance: discolouration may occur over time due to external influences.
Paintable: with most solvent-based and water-based paints.
Chemical resistance:
- Good resistance to: water, seawater, aliphatic solvents, oils, greases, diluted organic acids and alkalis.
- Moderate resistance to: esters, ketones and aromatic solvents.
- Poor resistance to: concentrated acids and chlorinated solvents.
Product properties
The key technical properties clearly listed in one place.
- Article number
- LIJ002241
-
Adhesive type describes the family of adhesive or sealant, such as epoxy adhesive, (methyl)methacrylate adhesive, polyurethane adhesive or polymer sealant. Its chemistry affects processing, curing, flexibility and adhesion. Products of the same type may still differ, so check the suitable substrates and application instructions.
- Polymeerkit
- Colour
- Transparant
-
The recommended application temperature range indicates the conditions under which the product can generally be applied and cured properly. Three temperatures matter:
- Air: the temperature in the workshop or outdoors.
- Substrate: the temperature of the surface being treated.
- Product: the temperature of the resin, adhesive or coating itself.
A cold substrate can cause condensation and affect adhesion. At higher temperatures, two-component products may react faster, reducing their working time. Check the dew point and follow the product instructions.
- 5-40 °C
-
The chemical base describes the chemistry of an adhesive, sealant, resin or coating, such as epoxy, polyester, polyurethane, (methyl)methacrylate or a hybrid polymer. It affects curing, flexibility and adhesion. Products with the same chemical base are not necessarily suitable for the same applications.
- MS polymer
-
The time after application during which a skin forms on the surface of a sealant. Tool the joint before the skin develops, as adjusting it afterwards can affect the finish or adhesion. Temperature and humidity influence this time.
- 5 minutes (23 °C 50% RH)
-
The time until the surface no longer feels tacky to a light touch. The material underneath may still be soft, so tack-free does not mean fully cured or ready for heavy loading.
- 40 minutes (23 °C 50% RH)
-
Curing time is the period a product needs to reach a specified stage of cure. It is usually given in hours or days, often at a reference temperature such as 20 °C. A product may be tack-free or safe to handle before reaching its full mechanical and chemical resistance. Film thickness and mixed quantity may also affect the time.
- 24-72 hours (23 °C 50% RH)
- Net contents
- 310 ml
Reviews
Frequently bought together
Useful additions for your project.